看 门狗的驱动一般来说比较简单，只要做寄存器的设置实现开启、关闭、喂狗功能。本项目中我们使用的是at91sam9g45处理器，带有看门狗定时器。这个 看门狗的驱动却比较复杂，应用层想用它的话，将涉及到boot引导设置，uboot配置及驱动，改写驱动程序。下面将逐步说明。
1、boot引导(bootstrap-v1.14)
由于该看门狗的MR寄存器只能写一次(Only a processor reset resets it.)，而默认情况下看门狗在boot引导程序中被关闭了，所以在boot引导程序中我们要开启看门狗。在at91sam9g45ekes.c文件的硬 件初始化函数hw_init中注释掉下面的配置即可开启看门狗：
/* writel(AT91C_WDTC_WDDIS, AT91C_BASE_WDTC + WDTC_WDMR); */
为了功能设置：我们配置如下：
writel(AT91C_WDTC_WDV | AT91C_WDTC_WDD | AT91C_WDTC_WDRSTEN | AT91C_WDTC_WDFIEN, AT91C_BASE_WDTC + WDTC_WDMR);
2、uboot配置及驱动(uboot-v1.3.4):
默认情况下，看门狗在uboot中没有配置，需要手动添加配置，在文件include/configs/at91sam9m10g45ek.h中添加如下配置
#define CONFIG_HW_WATCHDOG 1
#define CONFIG_AT91SAM9_WATCHDOG 1
此时编译uboot，会提示你找不到hw_watchdog_reset复位函数，这是因为虽然我们配置看门狗，但看门狗的uboot驱动并不存在，下面就来添加uboot下的看门狗驱动。
1）添加 include/asm-arm/arch-at91sam9/at91_wdt.h，内容如下
/*
* [origin: Linux kernel arch/arm/mach-at91/include/mach/at91_wdt.h]
*
* Copyright (C) 2008 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
* Copyright (C) 2007 Andrew Victor
* Copyright (C) 2007 Atmel Corporation.
*
* Watchdog Timer (WDT) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT91_WDT_H
#define AT91_WDT_H
#define AT91_WDT_CR (AT91_WDT + 0x00) /* Watchdog Control Register */
#define AT91_WDT_WDRSTT (1 << 0) /* Restart */
#define AT91_WDT_KEY (0xa5 << 24) /* KEY Password */
#define AT91_WDT_MR (AT91_WDT + 0x04) /* Watchdog Mode Register */
#define AT91_WDT_WDV (0xfff << 0) /* Counter Value */
#define AT91_WDT_WDFIEN (1 << 12) /* Fault Interrupt Enable */
#define AT91_WDT_WDRSTEN (1 << 13) /* Reset Processor */
#define AT91_WDT_WDRPROC (1 << 14) /* Timer Restart */
#define AT91_WDT_WDDIS (1 << 15) /* Watchdog Disable */
#define AT91_WDT_WDD (0xfff << 16) /* Delta Value */
#define AT91_WDT_WDDBGHLT (1 << 28) /* Debug Halt */
#define AT91_WDT_WDIDLEHLT (1 << 29) /* Idle Halt */
#define AT91_WDT_SR (AT91_WDT + 0x08) /* Watchdog Status Register */
#define AT91_WDT_WDUNF (1 << 0) /* Watchdog Underflow */
#define AT91_WDT_WDERR (1 << 1) /* Watchdog Error */
#endif
2）添加drivers/watchdog/at91sam9_wdt.c，内容如下
/*
* [origin: Linux kernel drivers/watchdog/at91sam9_wdt.c]
*
* Watchdog driver for Atmel AT91SAM9x processors.
*
* Copyright (C) 2008 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
* Copyright (C) 2008 Renaud CERRATO r.cerrato at til-technologies.fr
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
/*
* The Watchdog Timer Mode Register can be only written to once. If the
* timeout need to be set from U-Boot, be sure that the bootstrap doesn't
* write to this register. Inform Linux to it too
*/
#include <common.h>
#include <watchdog.h>
#include <asm/arch/hardware.h>
#include <asm/arch/io.h>
#include <asm/arch/at91_wdt.h>
/*
* AT91SAM9 watchdog runs a 12bit counter @ 256Hz,
* use this to convert a watchdog
* value from/to milliseconds.
*/
#define ms_to_ticks(t) (((t << 8) / 1000) - 1)
#define ticks_to_ms(t) (((t + 1) * 1000) >> 8)
/* Hardware timeout in seconds */
#define WDT_HW_TIMEOUT 2
/*
* Set the watchdog time interval in 1/256Hz (write-once)
* Counter is 12 bit.
*/
static int at91_wdt_settimeout(unsigned int timeout)
{
unsigned int reg;
unsigned int mr;
/* Check if disabled */
mr = at91_sys_read(AT91_WDT_MR);
if (mr & AT91_WDT_WDDIS) {
printf("sorry, watchdog is disabled/n");
return -1;
}
/*
* All counting occurs at SLOW_CLOCK / 128 = 256 Hz
*
* Since WDV is a 12-bit counter, the maximum period is
* 4096 / 256 = 16 seconds.
*/
reg = AT91_WDT_WDRSTEN /* causes watchdog reset */
/* | AT91_WDT_WDRPROC causes processor reset only */
| AT91_WDT_WDDBGHLT /* disabled in debug mode */
| AT91_WDT_WDD /* restart at any time */
| (timeout & AT91_WDT_WDV); /* timer value */
at91_sys_write(AT91_WDT_MR, reg);
return 0;
}
void hw_watchdog_reset(void)
{
at91_sys_write(AT91_WDT_CR, AT91_WDT_KEY | AT91_WDT_WDRSTT);
}
void hw_watchdog_init(void)
{
/* 16 seconds timer, resets enabled */
at91_wdt_settimeout(ms_to_ticks(WDT_HW_TIMEOUT * 1000));
}
3）添加drivers/watchdog/Makefile
#
# (C) Copyright 2008
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
include $(TOPDIR)/config.mk
LIB := $(obj)libwatchdog.a
COBJS-$(CONFIG_AT91SAM9_WATCHDOG) += at91sam9_wdt.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
all: $(LIB)
$(LIB): $(obj).depend $(OBJS)
$(AR) $(ARFLAGS) $@ $(OBJS)
#########################################################################
# defines $(obj).depend target
include $(SRCTREE)/rules.mk
sinclude $(obj).depend
#########################################################################
4）修改uboot的Makefile，主要是把watchdog编辑到工程里
修改1：
LIBS += drivers/video/libvideo.a
+LIBS += drivers/watchdog/libwatchdog.a(添加)
LIBS += common/libcommon.a
修改2:
TAG_SUBDIRS += drivers/usb
TAG_SUBDIRS += drivers/video
+TAG_SUBDIRS += drivers/watchdog (添加)
5）修改串口驱动drivers/serial/atmel_usart.c，主要是在串口读的时候复位看门狗，防止系统重启
int serial_getc(void)
{
- while (!(usart3_readl(CSR) & USART3_BIT(RXRDY))) ; (删除)
+ while (!(usart3_readl(CSR) & USART3_BIT(RXRDY))) (添加)
+ WATCHDOG_RESET(); (添加)
return usart3_readl(RHR);
}
3、改写驱动程序(linux2.6.30内核)
1、配置内核
在默认情况，系统并不加载看门狗驱动，需要配置内核：make menuconfig
Device drivers-->Watchdog Timer Support-->AT91SAM9 watchdog
注：在笔者的at91sam9g45处理器，编译后配置编译后还是不能加载，后花了很久时间才找出原因，看门狗配置项如下：
CONFIG_AT91SAM9X_WATCHDOG=y (.config文件)
而平台设备加载中(arch/arm/mach-at91/at91sam9g45_devices.c文件)
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
static struct platform_device at91sam9g45_wdt_device = {
.name = "at91_wdt",
.id = -1,
.num_resources = 0,
};
static void __init at91_add_device_watchdog(void)
{
platform_device_register(&at91sam9g45_wdt_device);
}
#else
static void __init at91_add_device_watchdog(void) {}
#endif
宏定义和配置项不符，难怪加载不进去，修改CONFIG_AT91SAM9_WATCHDOG为CONFIG_AT91SAM9X_WATCHDOG
正常启动，系统/dev目录下有watchdog设备
2、修改驱动
由于，该系统看门狗在处理器复位时才可以设置模式寄存器(MR)，所以看门狗一旦开启，就不能关闭。
查看看门狗驱动(drivers/watchdog/at91sam9_wdt.c)，我们发现驱动在平台驱动注册的时候at91wdt_driver函数中调用了：
setup_timer(&at91wdt_private.timer, at91_ping, 0);
mod_timer(&at91wdt_private.timer, jiffies + WDT_TIMEOUT);
调用内核定时器定时复位看门狗。当应用程序要使用看门狗时，可以从内核定时器列表中删除看门狗定时器，然后手动定时复位看门狗；当应用程序不使用时，再将看门狗定时器添加到内核定时器中。
这些操作我们放在IOCTL中，代码如下(at91_wdt_ioctl函数)：
switch(cmd) {
case WDIOC_SETON: //"开启"看门狗自动定时复位
setup_timer(&at91wdt_private.timer, at91_ping, 0);
mod_timer(&at91wdt_private.timer, jiffies + WDT_TIMEOUT);
return 0;
case WDIOC_SETOFF: //"关闭"看门狗自动定时复位，变位手动复位
del_timer(&at91wdt_private.timer);
return 0;
case WDIOC_KEEPALIVE:
//at91wdt_private.next_heartbeat = jiffies + heartbeat * HZ;
at91_wdt_reset();
return 0;
.....