DR模式中LVS主机与实际服务器都有一块网卡连在同一物理网段上。
IP分配
VIP:10.10.3.170
RIP1:10.10.3.140
RIP2:10.10.3.141
1、安装所需的依赖包
yum install -y wget make kernel-devel gcc gcc-c++ libnl* libpopt* popt-static
2、创建一个软链接，防止后面编译安装ipvsadm时找不到系统内核
ln -s /usr/src/kernels/2.6.-358.18..el6.x86_64/ /usr/src/linux
3、下载安装ipvsadm
wget http://www.linuxvirtualserver.org/software/kernel-2.6/ipvsadm-1.26.tar.gz
tar zxvf ipvsadm-1.26.tar.gz
cd ipvsadm-1.26
make && make install
4、编写并运行脚本（LVS服务器的脚本）
vi lvs.sh
#!/bin/bash
# -- by kgdxpr VIP=10.10.3.170
RIP1=10.10.3.140
RIP2=10.10.3.141 /etc/rc.d/init.d/functions logger $ called with $
case "$1" in start)
echo " start LVS of DirectorServer"
/sbin/ifconfig eth0: $VIP broadcast $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev eth0:
echo "" >/proc/sys/net/ipv4/ip_forward #Clear IPVS table
/sbin/ipvsadm -C
#set LVS
/sbin/ipvsadm -A -t $VIP: -s rr
/sbin/ipvsadm -a -t $VIP: -r $RIP1: -g
/sbin/ipvsadm -a -t $VIP: -r $RIP2: -g #Run LVS
/sbin/ipvsadm
;;
stop)
echo "close LVS Directorserver"
echo "" >/proc/sys/net/ipv4/ip_forward
/sbin/ipvsadm -C
/sbin/ifconfig eth0: down
;;
*) echo "Usage: $0 {start|stop}"
exit
esac
注：/sbin/ipvsadm -A -t $VIP:80 -s rr (rr代表轮询，还有分配方式)
/sbin/ipvsadm -a -t $VIP:80 -r $RIP1:80 -g (-g代表DR模式，还有其他模式)
5、给脚本加权限，并执行
chmod +x lvs.sh
chmod 755 /etc/rc.d/init.d/functions
./lvs.sh start
6、配置后端的WEB服务器脚本
vi realserver.sh
#!/bin/bash
# -- by kgdxpr
VIP=10.10.3.170
/etc/rc.d/init.d/functions
case "$1" in
start)
echo " start LVS of REALServer"
/sbin/ifconfig lo: $VIP broadcast $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev lo:
echo "" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "" >/proc/sys/net/ipv4/conf/all/arp_announce
sysctl -p >/dev/null >&
;;
stop)
/sbin/ifconfig lo: down
echo "close LVS Directorserver"
echo "" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "" >/proc/sys/net/ipv4/conf/all/arp_announce
;;
*)
echo "Usage: $0 {start|stop}"
exit
esac
7、给脚本加权限，并执行
chmod +x realserver.sh
chmod 755 /etc/rc.d/init.d/functions
./realserver.sh start