问题描述
因此，我正在学习x86的工作原理，并遇到人们说x86是字节可寻址的，但可以读取单词，双精度单词等.处理器如何决定何时使用哪种方法?例如.用于访问下一条指令以及当用户想要对存储器进行读/写操作时，使用哪种寻址模式?
So I am learning how x86 works and have come across people saying that it is byte-addressable, yet can read words, double words, etc.How does the processor decide which method to use and when?E.g. for accessing the next instruction and when a user wants to read/write to memory, which addressing mode is used?
推荐答案
每个内存访问都具有由机器代码指令指定的操作数大小.(寻址模式不是正确的术语:不同的寻址模式以不同的方式指定要访问的内存块的最低地址，例如 [rdi] vs. [rdi + rdx * 8] vs. [RIP + rel32] )
Every memory access has an operand-size specified by the machine-code instruction. (Addressing mode isn't the right term: different addressing modes are different ways of specifying the lowest address of the chunk of memory to be accessed, like [rdi] vs. [rdi + rdx*8] vs. [RIP + rel32])
使用前缀(对于整数指令分别为16 vs. 32 vs. 64位)或相同的助记符(8位整数)使用不同的操作码来对不同的操作数大小进行编码.或者带有可以使用xmm，ymm或zmm寄存器的AVX/AVX512指令的VEX或EVEX前缀中的位.
Encoding different operand-sizes is done with prefixes (for 16 vs. 32 vs. 64-bit for integer instructions) or a different opcode for the same mnemonic (8-bit integer). Or with bits in the VEX or EVEX prefix for AVX / AVX512 instructions that can use xmm, ymm, or zmm registers.
解码还取决于当前模式，这意味着默认的操作数大小:32和64位模式为32，而16位模式为16. 66 opererand-size前缀表示相反的大小.
Decoding also depends on the current mode implying the default operand-size: 32 for 32 and 64-bit mode, or 16 for 16-bit mode. A 66 opererand-size prefix implies the opposite size.
在64位模式下，REX前缀中的 .W (宽度)位将操作数大小设置为64位.(还有一些指令，例如 push / pop 默认为64位操作数大小，不需要前缀，但是大多数指令例如 add / sub / mov 仍默认为32位)
In 64-bit mode, the .W (width) bit in the REX prefix sets the operand-size to 64-bit. (And some instructions like push/pop default to 64-bit operand-size with no prefix needed, but most instructions like add/sub/mov still default to 32-bit)
还有一个 0x67 地址大小前缀，用于将寻址模式交换为其他大小.(16 vs. 32或在64位模式下64-> 32.)
There's also a 0x67 address-size prefix which swaps addressing modes to the other size. (16 vs. 32 or in 64-bit mode 64 -> 32.)
例如， mov [rdi]，eax 是双字存储，并且机器代码编码将通过在操作码上不对16/32/64位操作数使用特殊前缀来指定-尺寸.(有关可用的编码，请参见 https://www.felixcloutier.com/x86/mov .但是请注意，英特尔手册中没有在每个条目中提到 66 操作数大小的前缀:它具有2个相同的编码，但大小不同.您必须知道哪个需要 66 前缀(基于当前模式的默认值).
For example, mov [rdi], eax is a dword store, and the machine-code encoding will specify that by using no special prefixes on the opcode for 16/32/64-bit operand-size. (see https://www.felixcloutier.com/x86/mov for the available encodings. But note that Intel's manual doesn't mention 66 operand-size prefixes in each entry: it has 2 identical encodings with different sizes. You have to know which one needs a 66 prefix based on the current mode's default.)
16位操作数大小(如 mov [rdi]，ax )将具有相同的机器代码，并带有 66 操作数大小前缀.
16-bit operand-size like mov [rdi], ax will have the same machine code by with a 66 operand-size prefix.
8位操作数大小( mov [rdi]，al )有自己的操作码，不需要前缀.
8-bit operand-size (mov [rdi], al) has its own opcode, no prefixes needed.
movzx / movsx are interesting cases: the memory access size is different from the destination register. The memory-access size (byte or word) is specified by the opcode. Operand-size prefixes only affect the destination size. Except x86-64 63 /r movsxd (dword->qword sign-extension) where a 66 operand-size prefix does shrink the memory-access size down to m16 to match the destination.
类似于SIMD指令；指令编码唯一地确定内存访问大小以及读取或写入的寄存器.
Similarly for SIMD instructions; the instruction encoding uniquely determines the memory-access size, along with the registers read or written.
这篇关于在执行指令和读/写数据时，x86如何处理字节和字寻址?的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持！