问题描述
我有一个Perl脚本，该脚本执行各种安装步骤来为我们公司设置开发箱.它运行各种shell脚本，其中一些由于低于所需的ulimit s(在我的情况下，具体为栈大小-s)而崩溃.
I have a Perl script that does various installation steps to set up a development box for our company. It runs various shell scripts, some of which crash due to lower than required ulimits (specifically, stack size -s in my case).
因此，我想设置一个ulimit，该ulimit会应用于从我的主要Perl脚本中启动的所有脚本(children)，但是我不确定如何实现这一点-任何尝试从中调用ulimit的尝试在脚本中仅将其设置在该特定的子外壳上，该外壳立即退出.
Therefore, I'd like to set a ulimit that would apply to all scripts (children) started from within my main Perl one, but I am not sure how to achieve that - any attempts at calling ulimit from within the script only set it on that specific child shell, which immediately exits.
我知道我可以在运行Perl脚本或使用/etc/security/limits.conf之前调用ulimit，但是我不希望用户知道任何这些-他们应该只知道如何运行脚本，这应该为他们照顾所有这些.
I am aware that I can call ulimit before I run the Perl script or use /etc/security/limits.conf but I don't want the user to know any of this - they should only know how to run the script, which should take care of all of that for them.
我也可以在每次运行命令时都运行ulimit，例如ulimit -s BLA; ./cmd，但是我不想每次都重复此操作，我觉得这里有一个更好，更干净的解决方案.
I can also run ulimit every time I run a command, like this ulimit -s BLA; ./cmd but I don't want to duplicate this every time and I feel like there's a better, cleaner solution out there.
另一个疯狂的解决方法"是创建一个名为BLA.sh的包装脚本，该脚本将设置ulimit并调用BLA.pl，但是，这又是我的主意，现在我有两个脚本(我什至可以BLA.pl用"ulimit -s BLA; ./BLA.pl --foo"来称呼自己，并根据是否看到--foo而采取不同的行动，但这比以前更骇人了.
Another crazy "workaround" is to make a wrapper script called BLA.sh which would set ulimit and call BLA.pl, but again, it's a hack in my mind and now I'd have 2 scripts (I could even make BLA.pl call itself with "ulimit -s BLA; ./BLA.pl --foo" and act differently based on whether it sees --foo or not but that's even hackier than before).
最后，显然我可以安装BSD :: Resource，但是我想避免使用外部依赖项.
Finally, apparently I could install BSD::Resource but I'd like to avoid using external dependencies.
那么，在Perl脚本中设置ulimit并将其应用于所有子级的 方法是什么?
So what is THE way to set the ulimit from within a Perl script and make it apply to all children?
谢谢.
推荐答案
我最终在ulimit -s BLA之前添加了需要它的命令.我特别不想使用BSD :: Resource，因为它不是默认的Perl软件包，并且大约一半的现有开发机器都缺少它.没有用户交互是特定要求.
I ended up prepending ulimit -s BLA to the commands that needed it. I specifically didn't want to go with BSD::Resource because it's not a default Perl package and was missing on about half of the existing dev machines. No user interaction was a specific requirement.
这篇关于如何在适用于其子级的Perl脚本中设置ulimit?的文章就介绍到这了，希望我们推荐的答案对大家有所帮助，也希望大家多多支持！