我正在努力使PIC16F1829进入睡眠模式。当数据手册在深度睡眠模式下的报价为20nA时，该单元消耗的电流约为18mA。有人可以帮忙吗？
根据数据表，我必须执行以下“ WDT，BOR，FVR和T1OSC
禁用，所有外围设备都未激活”，我认为如下所示？
#include <pic16Lf1829.h>
#include <plib/adc.h>
#include <plib/pconfig.h>
#include <plib/usart.h>
// Use project enums instead of #define for ON and OFF.
// CONFIG1
#pragma config FOSC = ECL // Oscillator Selection (INTOSC oscillator: I/O function on CLKIN pin)
#pragma config WDTE = OFF // Watchdog Timer Enable (WDT disabled)
#pragma config PWRTE = OFF // Power-up Timer Enable (PWRT disabled)
#pragma config MCLRE = ON // MCLR Pin Function Select (MCLR/VPP pin function is MCLR)
#pragma config CP = OFF // Flash Program Memory Code Protection (Program memory code protection is disabled)
#pragma config CPD = OFF // Data Memory Code Protection (Data memory code protection is disabled)
#pragma config BOREN = OFF // Brown-out Reset Enable (Brown-out Reset disabled)
#pragma config CLKOUTEN = OFF // Clock Out Enable (CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin)
#pragma config IESO = ON // Internal/External Switchover (Internal/External Switchover mode is enabled)
#pragma config FCMEN = ON // Fail-Safe Clock Monitor Enable (Fail-Safe Clock Monitor is enabled)
// CONFIG2
#pragma config WRT = OFF // Flash Memory Self-Write Protection (Write protection off)
#pragma config PLLEN = OFF // PLL Enable (4x PLL disabled)
#pragma config STVREN = ON // Stack Overflow/Underflow Reset Enable (Stack Overflow or Underflow will cause a Reset)
#pragma config BORV = LO // Brown-out Reset Voltage Selection (Brown-out Reset Voltage (Vbor), low trip point selected.)
#pragma config LVP = ON // Low-Voltage Programming Enable (Low-voltage programming enabled)
int main(int argc, char** argv) {
/*******************OSCILATOR CONFIGURATION*************/
OSCCON = 0b01101000; // OSCILATOR CONTROL REGISTER 1MHz
BORCON = 0x00;
WDTCON = 0x00; // Enable watchdog timer
/*******************************************************************************/
/**********************PORT A,B,C SETUP*************************************/
ANSELB = 0b00000000; /* Enable Digital input = 0 or Analogue = 1*/
WPUB = 0b00000000; /* Enable PULL UP 1 = yes 0 - NO*/
TRISB = 0b00000000; /* Tri-state PIN*/
PORTB = 0b00000000; /* Set PORTB Logic */
WPUC = 0b00000000;
ANSELC = 0b00000000; /* Enable Digital input = 0 or Analogue = 1*/
TRISC = 0b00000000; /* Tri-state PIN*/
PORTC = 0b00000000; /* Set PORTB Logic */
WPUA = 0b00000000;
ANSELA = 0b00000000; /* Enable Digital input = 0 or Analogue = 1*/
TRISA = 0b00000000; /* Tri-state PIN*/
PORTA = 0b00000000; /* Set PORTB Logic */
IOCBP = 0b00100000; /* INTERRUPT-ON-CHANGE PORTB POSITIVE EDGE REGISTER*/
IOCBN = 0b00000000; /* INTERRUPT-ON-CHANGE PORTB NEGATIVE EDGE REGISTER*/
INTCON = 0b01011000; /* Enable int on PIN Change*/
/*******************************************************************************/
bit_set(INTCON,7); /*ENABLE GLOBAL INTERUPTS*/
ADCON0 = 0x00;
ADCON1 = 0x00;
T1CON = 0x00;
T2CON = 0x00;
FVRCON = 0x00; //FIXED VOLTAGE REFERENCE CONTROL REGISTER
CM1CON0 = 0x00;
CM1CON1 = 0x00;
CM2CON1 = 0x00;
CM2CON0 = 0x00;
PWM1CON = 0x00;
PWM2CON = 0x00;
DACCON0 = 0X00;
DACCON1 = 0X00;
T1CON = 0X00;
/********** MAIN LOOP START*******************/
for(;;) {
SLEEP();
}
最佳答案
这可能是缺少异常处理的结果。您启用了中断，但是没有捕获中断的功能。如果出于某种原因将设置一个中断标志，则没有任何要清除的标志，并且由于设置了GIE（即使处于睡眠状态），您的图片也会跳转到中断向量。由于未指定中断功能，因此（取决于您的编译器）您可能会最终进入未编程的存储区，并以全速执行任意指令。
尝试使用相同的代码：
--- INTCON = 0b01011000; /* Enable int on PIN Change*/
+++ INTCON = 0b00000000; /* Disable all int */
关于c - Microchip PIC16F1829深度 sleep ，我们在Stack Overflow上找到一个类似的问题：https://stackoverflow.com/questions/24258991/