我有类似的问题在这里（AVRISPmkII connection status: Unknown status 0x00），但不同的设置和改变比特锁没有帮助。
当前设置为ATMega328P，外部振荡器16MHz连接至AVRISP MKII编程器的ISP接口，但无论我做什么，它始终显示相同的输出：
mike@asus:~/wireless-temp-sens/tests$ sudo avrdude -p atmega328p -P usb -c avrispv2 -U lfuse:w:0xff:m -U hfuse:w:0xd9:m -U efuse:w:0xfe:m -v
avrdude: Version 6.0.1, compiled on Oct 21 2013 at 17:07:18
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/mike/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : usb
Using Programmer : avrispv2
avrdude: usbdev_open(): Found AVRISP mkII, serno: 000200209719
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500V2
Description : Atmel AVR ISP V2
Programmer Model: AVRISP mkII
Hardware Version: 1
Firmware Version Master : 1.23
Vtarget : 4.9 V
SCK period : 2053.39 us
avrdude: stk500v2_command(): command failed
avrdude: stk500v2_program_enable(): bad AVRISPmkII connection status: Unknown status 0x00
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude done. Thank you.
感谢您的帮助！
最佳答案
问题解决了！不记得到底是什么原因。我想时钟晶体在实验板上没有正确的连接。所以，我想说：
检查你的线路
检查你的线路
检查你的线路
关于linux - 无法通过AVRisp mkII与atmega328p通话，我们在Stack Overflow上找到一个类似的问题：https://stackoverflow.com/questions/27385064/